Batteries

The standard stompbox battery is the 9 volt PP3 configuration battery.

But what about battery types? Dry-cell, alkaline, rechargeable? There are lots to choose from, but only a few options that make sense in the context of stompboxes. First, let's look at the capacity ratings of different types of 9 volt batteries:

Capacity is measured in milliampere-hour  (mAH) which basically tells you the amount of steady current passed by the battery on one hour. You can see from the above chart that alkaline batteries provide more juice than standard carbon-zinc, but way less that Lithium. Unfortunately, lithium batteries are quite expensive and are not practical for stompboxes from a cost perspective.

Additionally, rechargeable batteries deliver abysmal mAH ratings compared to disposable ones, and are also inconvenient (who wants to keep popping the battery cover and yanking batteries? Not me.)

In general, alkaline batteries are the best types for stompboxes in terms of longevity. You can certainly get away with carbon-zinc, but they'll croak faster and at a more non-linear rate.

Which leads us to:

Never Buy Batteries at the Store

The markup on batteries at retail locations is unbelievable. You will typically see around 4 dollars for a name-brand alkaline 9 volt, and that is absolute insanity. Retail stores have a huge profit margin on batteries--don't play their game.

Instead, buy your batteries online through a bulk distributor. For example: a 9 volt alkaline Duracell for $1.50.

Finally, if you have to byy retail, get your batteries at a place like Costco or Price Club. Great bulk savings to be had there.

Which leads us to:

Skip Batteries Altogether

If you are serious about using effects and have, or are building, a pedalboard, ditch the battery equation altogether and go with AC-DC adaptors. We'll talk a bit more about this later, but for now, just add up the hundreds of dollars you are paying to retail stores for overpriced batteries that die and then get dumped in a landfill leading to toxic waste that will eventually lead to the zombie walking dead mutation apocalyptic scenario.

Over-Volting and Under-Volting

"Wait!" you may say. "Those are made-up terms!" Well you got me there. But they are convenient monikers to use when talking about two interesting aspects of voltage modification for pedal use.

Sometimes, folks will run 9 volt pedals at higher voltages using an AC-DC adaptor. For example, you may take an overdrive pedal that is nice, but when you boost it up to 12 volts you find that it sounds a lot better. Why is that? Because of headroom, as we discussed earlier. Increased voltage gives the pedal more usable headroom. It is interesting to experiment with over-volting pedals, but only within the following constraints:

• Ensure the pedal can support more voltage. Before you plug the pedal into an hopped-up adaptor, check with the manufacturer for the rated maximum voltage. Don't assume that it will work. Assume that it will fry the pedal.
• Over-volting is only useful on analog pedals. Analog pedals primarily use transistors and/or opamps to accomplish their magic. These analog devices are amenable to over-volting to increase headroom. Digital circuits expect what they expect or they refuse to work. Over-volt your Line 6 DSP pedal and at best it will just shut down, at worst it will become an ex-pedal.

Next, on to under-volting which is also known as "voltage sag". Some folks feel that certain pedals sound better when the battery is dying. This is common for fuzz, overdrive and distortion circuits. Why would a dying battery sound "better"? If you remember our discussion about headroom, it will be pretty bvious. Asthe battery becomes depleted, its available voltage and current decrease. This in turn decreases headroom and adds more compression and distortion.

Of course, waiting for you battery to achieve thegolden state of "mostly dead"-ness is hardly practical. So you can build a dying battery simulator, or use the Sag feature of a commercial power unit to achieve the same affect.

As with over-volting, under-volting does not make sense in the context of digital pedals. They are binary beasts, either the voltage is right or it isn't.

Current Draw

So enough about voltage already. What about current?Why is it important?

Each pedal is going to draw a specific amount of current out of the power source, whether that source is a battery or and AC-DC adaptor. A high current draw is going to deplete your battery faster. A higher current draw is also going to require a heftier AC-DC adaptor.

To put things in perspective, let's look at some examples of common pedals and their current draw:

As we start out at the top, we can see that analog designs based on transistors and opamps have rather miserly requirements in the range of 3mA to 15mA. These types of pedals can last quite long with a battery. But as we move up the food chain, we can see the pedals become increasingly greedy.

Indeed, for most pedals that draw 100mA or more, batteries are very impractical. In the user guide for the Boss DD-20 GigaDelay, it explains how to install 6 AA batteries, but then goes on to tell you these are for "testing purposes" only.

In today's world of increasingly complex stompboxes, and with the growing ubiquity of digital/DSP designs, battery usage is often not advisable. However, if even if you use AC adaptors, you still need to understand current draw, as we'll see when talk about AC-DC adaptors and power supplies.

How to Measure Current Draw

As you work through the powering issues associated with stompboxes and your pedalboard, you'll eventually need to know the current draw for your pedals because you'll want to ensure that your total draw is not exceeding your available power. You can search the interwebs for manufacturer's published current draw values for your specific pedals, but where's the fun in that? The most accurate numbers are going to come from your actual pedals, so knowing how to measure current draw is an important skill, and will also make you more attractive to women.

The good news is that it is very easy to do. First, get out your multi-meter. (What? You don't have a multi-meter? Get one post-haste. Being a serious pedal user/hacker/builder without a multi-meter is like being a duck and not having lips. Or something like that.)

1. Insert a plug into the pedal's input jack so it is powered on
    
2. Press the stompswitch so the pedal is on.
3. Pop open the pedal so you have access to the battery clip
    
4. Connect only the positive side of the battery
    
5. Set your multi-meter to read mA values in the 2-200mA range
    
6. Connect the meter's probe in series with the battery and battery clip
    
7. Measure the current draw

Pedals without Batteries

You can measure current draw on pedals without batteries also--it is just a bit more work. Use some wire, a DC jack and a DC plug. Like this:

It really is that simple. You might want to keep a list of all the measured current draw values for your pedals--these numbers will come in useful later if you are figuring out overall power requirements.

AC-DC Adaptors

An AC-DC adaptor is the wall-wart type device that you plug into the wall. It uses a step-down transformer to convert the mains voltage (120vAC here in the U.S., 240vAC overseas) down to a much lower value, typically anywhere from 3 volts to 40 volts. It then uses additional components to convert (or rectify) the AC into DC.

Unregulated Cheap Slop

Unregulated adaptors are based on primitive designs, and consequently, dirt cheap. The primitive cheapness comes into play in the part of the adaptor that converts AC into DC. With unregulated power supplies, a multi-diode configuration known as a bridge rectifier is responsible for the conversion. It is simple and cheap, but it is not ideal. Indeed, some double-cheap models don't even do a full bridge rectifier--two diodes is the minimum instead of four in this case.

First off, on an unregulated supply, the conversion from AC to DC does not result in pure DC. There is always some residual AC hanging out on the DC signal. This residual dirt is known as ripple and manifests itself in an audio circuit as noise.

Another drawback of an unregulated supply is that it will only deliver its rated voltage at a certain stated load.

Try this for fun: take the cheapest AC-DC adaptor in your collection. Read the output voltage rating, let's say that it is 12vDC. Plug it into the wall and use your multi-meter the check the output voltage. WTF? It is something like 14 volts. That is because an unregulated supply rated at 12 volts will only actually put out 12 volts when it has a load connected (like a pedal) that draws the exact current that the supply is rated for. This is generally not a terrible thing, but it leads to a lot of slop in the power supply's ability to provide the correct voltage to its user.

Finally, unregulated power supplies also generally lack any kind of filtering of other crap that may be on your mains. For example, mains-carried RFI and other mid to high frequency noise is not filtered out.

So, unregulated supplies are crap, but chances are that you own a lot of them. The good news is that most pedals have circuitry that does at least rudimentary filtering so noise and hum are reduced but typically not eliminated.

Regulated Power Supplies

Regulated power supplies (also known as switching power supplies) on the other hand are very nice. They use semiconductor-based AC-DC conversion and have at least adequate filtering. The resulting DC output is mostly devoid of residual AC ripple (less noise) and actually puts out the stated voltage regardless of load (better circuit stability).

So What Do I Use?

If you are like me, you have a box or drawer full of shitty AC-DC adaptors culled from a variety of broken, lost or obsolete devices. You keep them around and when you need power for a pedal, you dig through your box and try to find a match for voltage, current and tip polarity. And invariably, you end up with problems.

In an ideal world, you would use only high-quality regulated power supplies, and to the extent possible (as dictated by your budget), you should try to do this. Unregulated mystery supplies will add noise to your chain and you can never be sure about the actual voltage values being presented to your pedals.

The most common good-quality regulated power supply for pedals is the venerable Boss PSA-120, which provides 9.6 volts of regulated, filtered supply.

It can supply up to 200ma of current which will handle most of your single pedal needs. They are under 20 bucks a piece and are as reliable as all the other Boss products (which is pretty damn good). Of course, if you have 20 pedals, you'll be forking over around 400 dollars for AC-DC adaptors, at which point you want to start thinking about multi-supply units and daisy-chaining.

Power Supply Connectors

A particularly infuriating part of using AC-DC adaptors is the mismatch of connector types you'll find. Fortunately, the effects world has, for the most part, standardized on the Boss style 2.1mm barrel plug with a negative tip orientation.

Various problems are there to confront you. Here are the most common gotchas and how to address them.

Unknown Polarity
 

You have an AC adaptor with what appears the right barrel type connector, but you aren't sure it has the correct negative tip orientation for your Boss-style pedal.

Solution: First, check the label on the adaptor. Often there is a small graphic that shows the polarity. Like this:

f there is no graphic, you'll have to test the adaptor. Get out your multi-meter and plug the adaptor into the wall. Then stick the red meter lead on the barrel and the black lead in the tip. If it reads a positive voltage value, you have the correct polarity. If the meter shows a negative voltage, it is not the correct polarity for standard negative tip pedals.

Wrong Polarity

You have an AC adaptor with the correct voltage, current and connector size, but it is the wrong polarity.

Solution: Take your wire cutters and snip the cord about four inches from the base of the AC adaptor. Strip all four wires (two on each one). Twist them together, solder them, and wrap the whole thing up in electrical tape. For a better (and longer lasting) job, use heat-shrink tubing on each wire and then more on the finished job.

Wrong Tip

 

You have the right voltage and current, but the tip is the wrong type or size.

Solution: As with the previous example, you are going to cut off the plug and wire in a new one. In this case, you'll want to cut the plug off at around 4 to 6 inches from the plug end of the wire. Cut the old plug off, connect the new one, solder the wires (be sure to observe the correct polarity) and add some strain relief.

Building Your Own Daisy Chains

So let's say you have a multi-supply unit like the Pedal Power 2. Six of the outputs are rated at 100mA and two are rated at 200mA. If you measure the current draw of your pedals you will likely find that you have quite a few pedals that draw less than half of the 100mA current maximum.

Logically, you can power multiple pedals from one DC outlet as long as the total current draw for those pedals doesn't exceed the 100mA. It is always a good idea to leave yourself a little wiggle room, so 3/4 of the total power would be better. Let's assume the following scenario

So you have 100mA to work with. Some quick math shows that the combined current draw of 1, 2 and 3 is 100mA so you could theoretically daisy chain those three. Well-built units will handle that, but if you have a suspect adaptor, keep it to 3/4: i.e. only power 1 and 2, 1 and 3, or 2 and 3 from the same output.

Once you have calculated all the current draw figures and determined the permutations of multiple pedals to be powered from one port, it's time to get some daisy chain cables. You can buy them, but that will make you less cool, so why not build your own. Get some zip wire and 2.11mm DC connectors and follow the diagram below:

Living with Line 6 Pedals

No discussion of power supplies would be complete without at least some discussion of Line 6 pedals and their quirks and issues. For convenience, I'll split the topic into ToneCore pedals and Stompbox Modelers (DL4, DM4, FM4 and MM4).

The ToneCore Series

• The ToneCore series are digital pedals, but they do conform to the Boss standard: 9vDC adaptor into a 2.11mm negative tip supply.
   

• Like all digital pedals, batteries probably won't last too long, so use an adaptor. (See Line 6 Noise, below)
   

• Their recommended adaptor is the DC1 9.6v regulated power supply, 60ma, tip negative, but any standard Boss adaptor will do.

Stompbox Modelers

The Stompbox Modeler Series is sold with 9vAC adaptors. Wait a minute! AC? Yep, the suggested Line 6 adaptor for the stompbox modelers is the PX-2 power supply with an output of 9vAC at 2000mA. Why is that? Well Line 6 is a big company and for efficiency it is a good idea to have a single power supply unit that can power as many different devices as possible. So having an AC output device means that any device that requires AC gets it, and any device that requires DC can do the AC-DC conversion on its own.

So do you have to use the Line 6 9vAC adaptor? Not really. Both the Visual Sound OneSpot and the Voodoo Labs Pedal Power 2 support the Stompbox Modeler series with simple DC outputs. The Pedal Power 2 has two designated output jacks and DIP switch settings for Stompbox Modelers, so check the user guide before plugging in. Both units require a special cable to work with the Stompbox Modelers.

Line 6 Noise

Digital pedals in general, and Line 6 stuff in particular, can cause power supply noise that is a big problem with multi-pedal setups. In general, if you power your Line 6 gear with non-isolated power supplies (like a Visual Sound OneSpot) there is a good chance you are going to get noise in your other pedals, typically manifested as buzz or hum. This is because any supply line noise generated by a pedal is going to be interjected back into the power supply unit. If the power supply unit is not isolated, it is going to happily pass that noise on to all the other pedals.

So, if you use a non-isolated supply and are having noise with digital pedals, you are going to have to do one of two things:

• Power each of the digital pedals with its own dedicated AC-DC adaptor
   

• Switch to an isolated power supply like the Voodoo Labs Pedal Power 2.

Parts and Supplies

Here is a list of parts and supplies to help out with your pedal power projects.

Recommended Reading

• Jack Orman's Boosters and Distortion for some interesting reading on headroom, compression and distortion.
   
• Build Your own 60mA Power Supply! From Super Cool Smallbear. Or better yet, build your own 20ma Power Supply!